By Plumbing Guide for Bathtub Installation
By Plumbing Guide for Bathtub Installation
Blog Article
We've stumbled on this great article on A Step-by-Step Guide to Installing a Bathtub directly below on the web and decided it made perfect sense to relate it with you over here.
Installing a tub isn't exactly brain surgery, but it does need strong plumbing, carpentry, as well as sometimes, tiling skills. Changing an old bath tub with a new one is likewise a reasonably hard project. If the old tub is easily obtainable, the project can move immediately; if you need to open up a wall to get rid of the old bathtub as well as position the new bathtub, the job is much harder. In either instance, the project is within a home handyman's abilities, although you will certainly need an assistant to move out the old bathtub and set in the new one. See to it you have qualified on your own for the job as well as are comfortable attempting it. Instead of employing a service provider to take control of a halfway-completed task, it is much better to think about utilizing one before you start. Opportunities are you might need a professional plumber to make tube links.
This post will help you mount a new bath tub in your washroom if you have currently gotten a new bathtub and do not require to alter the setup of your previous water system pipes.
Your tools and also material list should make up the following:
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you need to do is detach the water system. After doing so, activate the faucets to drain pipes any type of water continuing to be in the system. The process of eliminating the existing taps can be rather troublesome because of the restricted access that is frequently the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a cloth prepared for the remaining water that will certainly come from the pipelines. When the supply pipelines have been gotten rid of, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from transforming during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Prior to going on to fit the brand-new faucets, compare the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic connector to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end offers a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin ensuring that the washing machines are in area in between the tap as well as the sink. Safeguard the tap in position with the manufacturer supplied backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal faucet adapters. The former kind needs to be linked to the faucet ends initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Bathtub
Using the two wooden boards under its feet, put the bath tub in the required position. The wooden boards are useful in uniformly spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 little points.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by examining the spirit level and also changing the feet on the bath tub up until the level reads degree.
To mount taps, fit all-time low of the outermost versatile faucet adapter to the suitable supply pipeline by making a compression join; then do the exact same for the various other faucet.
Switch on the water system as well as inspect all joints and also brand-new pipework for leaks and tighten them if required. Fill the tub and likewise check the overflow outlet and also the typical outlet for leaks.
Lastly, fix the bath paneling as explained in the maker's instruction manual. Tiling as well as sealing around the bathtub must wait until the tub has actually been used a minimum of when as this will settle it right into its last position.
Getting ready for the Installment
Firstly, the supporting framework provided with the bathroom should be fitted (if required) according to the producer's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is very important to see to it that if the faucet includes a plastic washer, it is fitted between the bath and the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets device to avoid strain on the bathtub.
Fit the adaptable tap connectors to the bottom of both taps utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you utilize every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath need to currently be ready to be suited its final placement.
Tiling Around the Bathtub
In the area where the bathroom satisfies the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to crack a rigid seal, triggering the water to permeate the wall surface in between the bathroom and also the tiling, bring about problems with moisture and also possible leaks to the ceiling below.
You can pick from a range of coloured sealants to assimilate your components as well as fittings. They are sold in tubes as well as cartridges, and are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always load the bathtub with water before securing, to allow for the movement experienced when the bathtub is in usage. The sealer can crack relatively very early if you do not take into account this movement prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally easily available on the marketplace. It is advisable to fit the floor tiles using waterproof or waterproof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you enjoyed our section about Installing A Bathtub. Thanks for spending some time to read our blog post. Are you aware of somebody who is enthusiastic about How to Install a Bathtub? Be sure promote it. Many thanks for your time. Come back soon.
End your worries, dial! Report this page